Until 20 December, winterising is free when you book and pay for an engine service, labour and consumables included. Book your outboard in for its service and we’ll winterise it at no extra charge, whatever the make. That’s how my dad ran the workshop and it’s how we’re running it this year. The workshop is booking up for the winter, so pick a slot early. Booking details are at the bottom of this page.
If you’d rather do it yourself, or you want to know what we’re doing to your engine, here’s the routine.
Servicing it yourself? Until 20 December, every service kit in our web shop comes with a free winterisation kit, everything for the lay-up included. Find the kit for your engine here. Can’t see one for your engine? Send us the make, model and hp and we’ll email you a payment link for the right kit, winterise kit included.
The first warm weekend of spring is when half of North Wales finds out their outboard won’t start. The engine didn’t break over the winter. It was put away tired, with old fuel in it and salt on everything, and it sat there for five months quietly getting worse.
Winterising isn’t hard. When I do one, I start at the bottom of the engine and work my way up. That way I don’t miss anything, and I don’t end up with grease on the cowl. Here are the ten checks I do, the same as in the video above, on a 20hp Tohatsu that came in for its lay-up.
1. The prop and the shaft
Spin the prop and watch the shaft. If it wobbles, it’s bent, and you want to know that now, not in April. Look over the blades for chips and bends.
2. Grease the prop shaft, thrust washer first
Take the prop off and grease the shaft. Salt water goes for it more than anywhere else, and you can never have too much grease in the marine environment.
When it goes back on, the order is thrust washer, prop, spacer, nut, then a new split pin. Forget the thrust washer and the prop pushes into the gearbox housing the first time you go into forward gear. It’s a mistake you make once. I made it at sixteen and haven’t made it since.
3. Gearbox oil: condition
Leave the engine upright for an hour so any water or metal settles to the bottom. Crack the lower drain plug and let out a drop, no more. Rub it on the back of your hand. Gritty means the gearbox is wearing. Milky means water is getting in, and the gearbox needs a pressure test to find out where.
4. Gearbox oil: level
Top up from the bottom hole until oil shows at the top one, then put both plugs back. I check this twice a season on my own engines, because water in a gearbox does its damage fast.
5. The mounts
Grab the engine and push and pull. You’re feeling for slop in the lower and upper mounts. A bit of give is fine. A clunk isn’t.
6. Grease the swivel and the tilt
Pump grease into the swivel bracket nipple until it comes out of the top and the bottom. Spray the tilt lock and the tilt tube, and work them a few times so it gets right in.
7. The steering cable
Pull the steering cable out, grease the inside, push it back and turn the wheel so the grease goes all the way down. After seized props, this is the most common thing I see jammed solid in spring. It takes five minutes.
8. Under the cowl
Check the engine oil on the dipstick. If it’s clean and on the top mark, leave it. If it’s dirty, change the oil and the filter now, not next year, because dirty oil sitting all winter is acidic. Look for corrosion, loose fixings and anything that looks wrong. If the fuel filter has a little red float in it, the float should be sitting at the bottom. If it’s floating, there’s water in your fuel.
9. Treat the fuel and run it
Modern pump fuel goes off. E10 is like keeping a sponge in your tank. I’d put Aspen in for the lay-up. If you’re stuck with pump fuel, put a stabiliser in at the rate on the label. In the video I used the Lucas one we sell.
Then put the engine on the flush muffs and run it for fifteen to twenty minutes. The treated fuel needs to get through the lines, the pump, the filter and the injectors or carb. If it doesn’t get that far, you’ve done half the job. While it runs, spray anti-corrosion on the bare metal and the starter, and clear grease on the electrical connections.
10. Fog it and check the anodes
With the engine warm and on a fast idle, take the air box off and spray fogging oil into the intake until it smokes, then switch off. That coats the insides for the winter. If you want the full fogging routine, cylinder by cylinder, Dad’s version is here: Bill Higham’s outboard winterisation process.
Last of all, look at the anodes on the gearbox, the trim tab and the bracket. If they’re eaten away, replace them. They’re cheap, and in salt water they’re the difference between the anode corroding and your engine corroding.
Or let us do it
Some of that is dead easy and some of it isn’t, especially the gearbox if the oil comes out milky. Until 20 December, winterising is free when you book and pay for an engine service, labour and consumables included, and we do every make of outboard. The workshop is booking up for the winter. Book the service and tell us you want it winterised at the same time. You can pick a slot online here, or ring the workshop on 01248 665666.
If you’re on the Seaworthy Service Club, winterisation is part of your plan, so just book the slot. If you’re not, the Service Club covers the lay-up, 10% off labour and priority booking, from £280 a year for a 15hp on Basic.
What you need: marine grease and a grease gun, gearbox oil and a pump, pliers and a socket for the prop nut, new split pins, anti-corrosion spray, fogging oil, flush muffs, and Aspen or a fuel stabiliser.
If you think I’ve missed a step, tell me in the comments. Everyone has their own way of putting an engine to bed.
